Modded Raptors Forum banner
1 - 20 of 25 Posts

·
Portsculptor
Joined
·
2,604 Posts
Discussion Starter · #1 ·
Cylinder head that is......
By default off the "corporate raptor" site.:lol:
Before and after:







 

·
Registered
Joined
·
263 Posts
looks awesome!
 

·
R.I.P. Coop
Joined
·
2,192 Posts
My current hp rating before this P&P is 48.13, now for the torgue numbers, this will have to wait until I get home as I can not remember this number... and for the peak speed on the dyno with dyno tires it was 84 mph.
 

·
Portsculptor
Joined
·
2,604 Posts
Discussion Starter · #6 ·
With your current #s you should be 58-60rwhp after all of the parts are swapped out depending on the tune.
 

·
Registered
Joined
·
2,177 Posts
looks good.
 

·
Registered
Joined
·
206 Posts
Seven are you going to sell your old head? I am assuming you P&Ped the head you just bought.
 

·
Registered
Joined
·
2,177 Posts
i pretty sure he is saving the stock to put back on when he and if he sells the bike
 

·
R.I.P. Coop
Joined
·
2,192 Posts
My current hp rating before this P&P is 48.13, now for the torgue numbers, this will have to wait until I get home as I can not remember this number... and for the peak speed on the dyno with dyno tires it was 84.88 mph.
Ok I do not have a scanner.
So here are my 'Run Files' without the curves as well as A/F Ratio:

RunFile_001.drf - 02/09/2008 12:59:17 PM Run Type: RO Run Conditions: 59.69 F, 28.47 in-HG, Humidity: 35%, STD: 1.04 Max Power = 47.23 Max Torque = 41.59 Max Speed = 84.42

RunFile_002.drf - 02/09/2008 1:14:39 PM Run Type: RO Run Conditions: 64.24 F, 28.49 in-HG, Humidity: 29%, STD: 1.04 Max Power = 47.66 Max Torque = 42.45 Max Speed = 84.32

RunFile_003.drf - 02/09/2008 12:21:15 PM Run Type: RO Run Conditions: 56.17 F, 28.49 in-HG, Humidity: 36%, STD: 1.04 Max Power = 47.89 Max Torque = 42.31 Max Speed = 84.88

RunFile_004.drf - 02/09/2008 1:28:33 PM Run Type: RO Run Conditions: 54.70 F, 28.49 in-HG, Humidity: 38%, STD: 1.03 Max Power = 47.63 Max Torque = 42.32 Max Speed = 84.56

RunFile_005.drf - 02/09/2008 1: 37:06 PM Run Type: RO Run Conditions: 54.10 F, 28.47 in-HG, Humidity: 39%, STD: 1.03 Max Power = 47.71 Max Torque = 42.08 Max Speed = 84.86

RunFile_006.drf - 02/09/2008 1:40:47 PM Run Type: RO Run Conditions: 54.42 F, 28.48 in-HG, Humidity: 40%, STD: 1.03 Max Power = 47.91 Max Torque = 42.06 Max Speed = 84.56

RunFile_007.drf - 02/09/2008 1:45:56 PM Run Type: RO Run Conditions: 54.10 F, 28.47 in-HG, Humidity: 40%, STD: 1.03 Max Power = 47.96 Max Torque = 42.15 Max Speed = 84.79

RunFile_008.drf - 02/09/2008 1:52:03 PM Run Type: RO Run Conditions: 53.43 F, 28.47 in-HG, Humidity: 40%, STD: 1.03 Max Power = 48.13 Max Torque = 42.31 Max Speed = 75.08

Based off of these stats Bo, does anything change or more importantly, what would be my Max Torque?

Please advise!
 

·
R.I.P. Coop
Joined
·
2,192 Posts
Additionally 'yamaboy' we going to have to hook up with dat dyno guy from Washington, PA... Soon! I needz to get it all installed and off to lil Washington we shall go!
 

·
WILD ONES
Joined
·
887 Posts
The above Run Files are not Bo's handy work. The above RunFiles are strictly, bolt-on applications!

I was speaking of the head job:lol::beerchug:

I sure hope you aren't pulling 48hp and 42ft lbs of tq with those mods in your sig... I'd want my money back!
 

·
Registered
Joined
·
49 Posts
I was speaking of the head job:lol::beerchug:

I sure hope you aren't pulling 48hp and 42ft lbs of tq with those mods in your sig... I'd want my money back!

No thats his new build. He should be push mid 60's now. I know with my set up i was push 60hp with no head work and no custom timing curve just curve two.
 
1 - 20 of 25 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top